Windscreen repair kit

Description

Suitable for all laminated glass. Makes pebbles and cracks less visible and stops them cracking further. Not suitable for cracks larger than 30cm and cracks running out to the edge of the glass. Reusable - enough in the pack to repair multiple spots. The kit removes the air from the crack and fills it with the repair agent. The material solidifies under UV light (use UV lamp or direct sunlight). For multi-layered glass, repairs only one layer. For best results, use the kit immediately after the damage has occurred, when water or dirt has not yet penetrated. If the damage is already black and damp, there is a chance that the substance will not absorb properly for a satisfactory repair.

Patching:

1. Avoid direct sunlight at the start of the repair.
2. Do not direct sunlight to the area to be repaired.cClean the damage with dry, clean paper.cThe glass damage should be dry and clean. If necessary, remove loose pieces of glass with the blade provided.
3. Fit the suction cup holder (A) so that its hole is in the centre of the defect (Figure 2).
4. Screw the guide (B) into the holder so that it presses gently against the centre of the defect (fig. 3,4).
5. Open the substance bottle (D) and drop 3-6 drops (depending on the size of the injury) into the guide (B). 3. When the substance starts to flow from the bottom, tighten the guide by gently twisting it.
6. Now screw in the compression nozzle (C) into the guide (B) to the end (picture 6). Allow the substance to soak into the defect for about 4-6 minutes.
7. Screw on the nozzle (C) 1/4 to 1/2 turn to ensure complete absorption.
8. Remove the nozzle (C) to allow air to escape from the reservoir (A).
9. Replace the nozzle (C) to extract the last of the air from the damage to the glass.
10. Now look at the damaged area from a 45 degree angle from inside the glass. If any air bubbles remain, repeat steps 6-9 again.
11. If no air is visible, remove everything from the glass.
12. Wipe off any excess material from the glass with a paper towel.
13. Where the damaged area is still visible, place a small drop of the substance directly on it. Now place the drying film (E) on the damaged area where the substance was used. Do not press the drying film.
14. Move the vehicle into direct sunlight or use a UV lamp. The drying time is 5-10min. depending on the intensity of the light. If there is no direct sunlight, the substance will take longer to dry.
15. Remove the drying film.
16. Check that the substance has dried. Take the blade(F) and scrape off the excess material.
17. Repeat steps 13 to 15 if the damaged area is still visible.

1. 1 Avoid direct sunlight at the start of the repair.
2. 2 Clean the damage with dry, clean paper.
3. Do not direct sunlight directly onto the damaged area.
4. Dry and dry with dry water and dry cloth. If necessary, remove loose pieces of glass with the blade provided.
5. Apply the repair material to the glass block at a rate of 3seconds to 1cm.
6. View the crack from a 45 degree angle so that the crack is filled with the material.
7. Allow to absorb for 5-10min.
8. If any air remains, press the glass from the inside until the air comes out. Press gently so as not to enlarge the crack.
9. Once the air has been removed, reapply the substance over the entire crack.
10. Apply the curing film(s) to the entire repaired area.
11. Move the vehicle into direct sunlight or use a UV lamp. The drying time is 5-10min. depending on the intensity of the light. If there is no direct sunlight, the material will take longer to dry.
12. Remove the curing film.
13. Check that the substance has dried. Take the blade(F) and scrape off the excess material.

• Secure payment options We only use the safest payment systems.
• 14-day return policy We do our best to keep our customers happy.
• Fast delivery across Estonia Quality auto parts delivered to your door